BlackBerry Forums Support Community

Closed Thread
Thread Tools
Old 11-04-2020, 02:03 AM   #1
New Member
Join Date: Mar 2016
Model: 7100T
Carrier: IPAD
Posts: 1
Default Lining method of EAF bottom ramming material

Please Login to Remove!

Lining preparation

Clean up the permanent layer residue, dust, iron wire, plastic cloth and other foreign objects. Calculate the knot size, the actual knot thickness is equal to the required knot thickness multiplied by 1.09, and a sufficient amount of ramming material should be prepared according to the construction furnace slope and furnace bottom size requirements. After receiving the material, check whether the ramming material has debris and damp. The debris should be cleaned up. The damp material should not be used, and knotting equipment such as rammers and pneumatic picks should be prepared.

Lining method
After shoveling the material flat with a shovel, step on it with your feet to remove the air, insert the steel drill into the material and shake it repeatedly, and then use your feet to further solidify. The construction thickness of each layer of ramming material is 150~200mm. Appropriate, and then use a knotting implement to repeatedly beat it 3 times in a spiral from the periphery to the center.

The method to check the quality of knotting is usually to put a round steel with a diameter of 5mm on the ramming layer and press it down with a pressure of 10kg, and its depth does not exceed 30mm. Steel drills can be inserted forcefully during site construction, and the depth should not exceed 30mm.

The method of knotting the furnace slope is the same as that of the furnace bottom. First, use your feet firmly, and then use the knotting appliance to ram, the maximum angle between the furnace slope and the furnace bottom does not exceed 40. Prevent rolling or collapse due to the furnace slope is too large.

Place bricks at the tapping mouth, furnace door and other places where molten steel is agitated and scour severely should be beaten vigorously and appropriately thickened to extend the service life of refractory materials in these damaged parts as much as possible.

After the ramming is finished, cover the 5~10mm thick steel plate on the ramming material to prevent the shape of the furnace bottom being damaged or the waste steel penetrates the ramming material layer when loading the scrap steel, which may cause the hidden danger of steel leakage. If steel cannot be made in time, 100~200mm thick lime is added to the iron plate to prevent the ramming material from hydrating.

We Changxing Refractory Material Co.,LTD is professional manufacturer and supplier of refractory materials for more than 30 years. Our high quality refractory products are good sold to many countries say South Africa, Bangladesh, Indonesia, Malaysia, etc.

Article Source:Lining method of EAF bottom ramming material
Company name: Henan Xinmi Changxing Refractory Materials Co.,Ltd
Old 11-04-2020, 08:38 PM   #2
BlackBerry God
tsac's Avatar
Join Date: Mar 2005
Location: Others run out when we run in
Model: Z10
OS: Cheerios
PIN: No Pin just a Tack
Carrier: at&t
Posts: 10,030
Default Re: Lining method of EAF bottom ramming material

You do realize this is a cell phone forum ?
Z10 on BES
Z10 on BIS
Closed Thread

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads for: Lining method of EAF bottom ramming material
Thread Thread Starter Forum Replies Last Post
Unable to view WebConsole airalex BES Admin Corner 0 09-20-2010 11:00 AM
Issue related to phoneListener Developer Forum 1 05-22-2008 03:25 AM

PHP Warning: Invalid argument supplied for foreach() in ..../parts/ebay-function.php on line 84

Copyright 2004-2016
The names RIM and BlackBerry are registered Trademarks of BlackBerry Inc.