TOLEDO TRANSDUCERS INC. 2 LOAD SENSORS, 2 TQM 700 MONITORS, 60,000LB TRANSDUCER For Sale
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
TOLEDO TRANSDUCERS INC. 2 LOAD SENSORS, 2 TQM 700 MONITORS, 60,000LB TRANSDUCER :
$750.00
TOLEDO TRANSDUCERS INC. 2 LOAD T400 SENSORS, 2 TQM 700 MONITORS,60,000LB TRANSDUCER
All in like new condition!
Monitor information
The TQM is important for powdered metal, compaction,insertion, staking and in-die applications. It is used with \"in-line\"load cells and strain gauges. Die setup, SPC work and quality assurance aremade easier when using a TQM Tonnage Monitor. Not only will it monitor force,but it will assist in protecting your investments by reducing downtime,improving productivity and improving product quality.
Manual alarm setpoints
Automatic setpoints
Displays total force
Low alarm can be disabled
High & low set point display switch
Excellent electrical noise rejection
Capacity alarm
Four or six digit display
One or two sensor inputs
Analog output jack
Automatic Zero Balance
Use with load cell or T400 sensors
Part counter
Reverse load display
High Immediate
Time based signatures
Pressroom networking
No. Of Channels
One
Sensor Inputs
Full bridge strain gauge sensors
120 to 1000 ohms
Up to (2) 350 ohm sensors
Sensor Excitation
Built-in 5VDC @ 70mA max (Short circuit protected)
Balance Range
+/- 1mV/V of offset
Gain Range
Low Gain = 0.568mV/V to 5.000mV/V
High Gain = 0.057mV/V to 0.625mV/V
Analog Output
35mm stereo phono jack
2.5VDC @ Press Capacity
+/- 1% of full scale max
+/- .1% of full scale max
Flat DC to 1KHz
Display
4 or 6 digit display
Display Update
Every Stroke (up to 2 updates per second max)
1024 or 2048 count
SPM
400 SPM (threshold trigger)
2000 SPM (probe trigger)
Calibration Shunts
1 Meg Ohm .1% precision resistor
RS-485
Trigger
Probe or Threshold
Threshold Probe
Built-in voltage source (12VDC @ 50mA max) provides power for NPN or PNP proximity probes. Also supports limit switch, solid state or mechanical relays
Resolver Interface
No
Shutdown Relay
7.5A @ 120VAC
N.O. and N.C. Contact
Bypass switch available
Power Req.
18 Watts max, 85-140VAC @ 50-60Hz OR
170-280VAC @ 50-60Hz
Operating Temp.
0-70 degrees Celsius
Weight
4.33 \"
6.06 \"
7.52 \"
Load sensor
The T400 is a tough and reliable bonded strain gauge sensor.When it is properly affixed to an operating machine, it provides an electricalsignal proportional to the load. Toledo Monitors and Modules digitally displaythe tonnage information as a calibrated value. It measures tension orcompression and in tons or pounds. The sensor can be installed on weld pads orby drilling and tapping. Hardware for both methods is included in the sensorkits. A Micro size is also available.
Quick and easyinstallationMeasure tension orcompressionAccurately measures intons or poundsUsed on all types of pressesHigh output straingauge based designA Micro size alsoavailableUsed in all ToledoMonitoring SystemsWaterproof
Hole Centers
Excitation Voltage, Typical
10 VDC or AC rms
Excitation Voltage, Maximum
15 VDC or AC rms
0.02% of load/Deg. Fahrenheit
Rated Output with
Weld Pads, Typical
1mV/V at 400 micro-inches/inch
Rated Output,
Balance
+/- 0.10 mV/V
Maximum Strain,
Safe
600 micro-inches/inch
17-4 PH stainless steel
Cable
4 conductor, shielded, oil resistant, polyurethane jacket
0.25 \"
1.00 \"
2.19 \"
We are not just another machinery broker.
We will ship this item and cost will vary by buyer location. Ifyou need a shipping rate just let us know.
Be sure to add us to your favorite sellers list for dailyadditions!!!
Loaded on truck – No charge
Payment isexpected within 7 days of sale end. Buyer is responsible for all freightcharges.
6% Michigan salestax where applicable.
Machines willneed to ship on a flatbed truck. If planning to ship in an enclosed trailer itwill need to be crated. Crating charges are extra.
If you have any questions or if you would like to schedule aninspection please contact us.
It is the user’sresponsibility to provide proper safety devices and equipment to safeguard theoperator from harm for any particular use, operation or set up, and tosafeguard adequately the machine or machines to conform to all Federal, Stateand Local Government Safety Standards, and all Industry Safety Standards.
MDNA returnprivilege applies to all machines (unless sold as-is). We will accept (within30 days of shipment) any machines and equipment, freight prepaid, for refund ofthe purchase price if proven mechanically unsatisfactory; or repair at dealer’soption.
Machines areshipped F.O.B. our plant. If damages are to occur during shipment it becomesthe freight company’s responsibility.
It is important that youcontact us with in 24 hours. You need to inform me of how and when youwill pay for your item and how you plan on shipping it. If you do not contactme within 10 days it will be treated as a non paying buyer and the appropriateaction will be taken.Related Items:
Toledo Transducers TR-1 Resolver
$310.00
Toledo Transducers Inc. SS1326-15 Transducer
$399.23
Toledo Transducers TTLM-4-255K I/O Load Module TTLM4255K
$399.99
