DY10 Power Supply / Source for 90 - 100W W2 / S2 CO2 Laser Tube AC 110V For Sale

DY10 Power Supply / Source for 90 - 100W W2 / S2 CO2 Laser Tube AC 110V


This item has been shown 2 times.

Buy Now

DY10 Power Supply / Source for 90 - 100W W2 / S2 CO2 Laser Tube AC 110V:
$139

DY10 Reci Power Supply / Source for80W - 100W W2 / S2 CO2 Laser Tube AC 110V



Mark & model:DY10, small size, quick response, it is suitable for Reci W2/S2 laser tube.

Original:Asia and Pacific Area China

Quality standard:International
H.S. Classification:Machinery & Electronics Electr. Element 8541 Semiconductor devices; light - emitting diodes parts.Warm tips:The power supply is to be used for Reci, EFR and WEEGIANT laser tube.If you want to make it work on other brands, please check the specification before - style="margin: 0px; padding: 0px; line-height: - resistingInput - Output,input - machinehull: ~ 40),Relativehumidity: power supply / power source adopts thin type design. The shape of this power supply / power source is thin which is specially designed for special laser tube.The power supply / power source makes laser tube output larger and more stable.
Quick Response: It can enlarge laser power and prolong laser tube‘s service life.
Easy Control: The start and stop of laser can be easily controlled by TTL level.
This power supply / power source has output open circuit protection.
This power supply / power source has TTL signal indication, water through signal indication and laser output indication.
This power supply / power source has the BUTTON to test it work and cut acrylic, fabric, double color sheet and rubber, etc
We stick the protection film on the power source to prevent the metal parts of the scrape!I. Instruction for sub - connection wire of the control end1) Footer 1 is 5V power supply / power source. (Not needed when connecting the cardinal plate. It is used when regulating the power with potentiometer and the 5V current should be less than 10 mA.2) TH. TL refers to high and low power level respectively, and WP refers to water protection.3) Footer 5 G refers to ground and 6 refers to input end.4) When connecting the control plate, connect the light signal with footer 2 in the case of high power level light-emitting, (footer 3 for low power level light-emitting), connect the ground-wire with footer 5, connect footer 6 with power control analog signal, and make short circuit for footer 4 and 5.5) PWM can also be used in footer 6, but the pulse peak is required to reach 5V, and the frequency should be above 20K.6) For testing: 3, 4 and 5 are in short circuit (or 4, 5 are in short circuit and 3, 5 are connected to switch), the potentiometer center is connected with 6 IN, and the two other ends are connected to 5V and ground (1 and 5) respectively.7) The high power level controls the light, 1 and 2 are connected, and 4 and 5 are in water protection.8) It is not proposed to control laser power with high-frequency modulation, because it will have impact on the service life of the laser.9) The model is applicable to Z2/S2 laser, it is necessary to regulate and use the current according to the laser instructions.10) The ammeter is concatenated to the cathode line.
II. Instruction for power wireNote: The table 10A refers to the connection wire requirement, but not the actual power dissipation.
III. Instruction for laser connection wire1) The positive red - line with high voltage is connected to the laser tail2) The negative white - line is connected to laser output window
IV. Current limitationTo limit the working current, the potentiometer (Lies in the underside of the power supply / power source should be rotated in counterclockwise (Please refer to the schematic diagram in our website). Limit the maximum output current as it is regulated in the operating instruction. The working current should be limited before delivery.
V. Linear scale between input signal and the output currentTurn around the potentiometer; the linear scale will be changed: for example, when the input signal is 0 - 5V, the output current is 0 - 32mA.Or when the input signals 0 - 2V, the output signal is 0 - 32mA.Note: When the potentiometer is turned down too much, the real output current will be brought down by the same input signal.
VI. Using currentThe use standard for our power supply / power source is under 220V, 50Hz. The fluctuation of the input voltage and frequency will affect the working current provided by the power supply / power source, the impact is linear relative. The unstable of the input voltage will affect the output power of the laser tube. The fluctuation of the input voltage has no impact on the lifespan of the laser if only the current provided by thesupply / power sourceis not over the current limitation.
  • EUB to USA: 7-15 working days
  • Other countries: by Singapore / Hong Kong Registered Air Mail:
  • We ship items out on Monday-Friday.
  • Shipping will be made within 1-2 business days when the payment is confirmed .
  • We only ship to the confirmed address provided by PayPal. Before you pay, please check your address in PayPal
  • We acceptPayPal(Allows you to pay by credit cards, debit cards or e checks securely with no surcharge).
  • If you have difficulty to make payment by PayPal please contact us for alternative payment method.
  • We are Paypal verified seller, you will feel comfortable to do business with us.
  • We DO NOT refund for shipping fee.
  • We accept return only in New Condition .
  • Full Refund as soon as merchandise is returned.
  • We can accept the return item within 14 days after the buyer receives it.
  • We will automatically leave positive response after receiving positive response from you.

  • If you have any issue with your purchase, please contact us before you leaveresponse .
  • Email:



Buy Now

Xantrex Xhr 7.5-80 Dc Power Supply, Tested, Working picture
Xantrex Xhr 7.5-80 Dc Power Supply, Tested, Working


Idec Ps5r-f24 120w Power Supply picture
Idec Ps5r-f24 120w Power Supply


Lambda Lls-6060  Power Supply  0-60volts  2.8 Amp picture
Lambda Lls-6060 Power Supply 0-60volts 2.8 Amp


Sorensen Xpl30-1 Dc Power Supply, 30v / 1a / 30w picture
Sorensen Xpl30-1 Dc Power Supply, 30v / 1a / 30w


Popular Forums